臻意国际有限公司
Gainer International (China) Limited
Repeater with touch screen support Dualband/
Tri band Wideband System(10dbm-23dbm)
1. The line shows the working status of system
2.The line shows the working status of system
3.The line shows the working status of system
4. 5 bars of the output signal strength indication, which shows you the maximum output power of the repeater. Each signal bar represents 5dB.
5. The specific value of the input signal strength measured in dBm, tell us the exact input signal level.
6. Uplink Sleep Mode. The uplink of the repeater is in standby mode when there is no call or data transmission. It will activate immediately when a call or data session is initiated.
7. Show the UL&DL maximum gain.
8. Antenna Isolation Detection. When first power on the repeater, it will detect the oscillation automatically between the outdoor antenna and indoor antenna.
9. Enter for selection or confirm the settings.
10. Back to the previous page or cancel the settings.
11. Increase the gain.
12. Decrease the gain.
13. Smart function. The repeater could set the gain automatically to prevent the Alarm. Press this icon to turn ON or turn OFF this function.
Electrical specification
Uplink
Downlink
Frequency Range
GSM900Mhz
890 ~ 915MHz
935 ~ 960MHz
DCS1800MHz
1710 ~ 1785 MHz
1805 ~ 1880 MHz
WCDMA2100MHz
1920 ~ 1980 MHz
2110 ~ 2170 MHz
Max .Gain
GCPR-GDW10
≥ 65dB
≥ 65dB
GCPR-GDW15
≥ 65dB
≥ 70dB
GCPR-GDW20
≥ 70dB
≥ 70dB
GCPR-GDW23
≥ 70dB
≥ 75dB
Max .Output Power
GCPR-GDW10
≥10dBm
≥12dBm
GCPR-GDW15
≥12dBm
≥15dBm
GCPR-GDW20
≥15dBm
≥20dBm
GCPR-GDW23
≥15dBm
≥23dBm
Band width
Wide Band
MGC (Step Attenuation Via Touch Panel )
≥ 31dB / 1dB step
Automatic Level Control
≥ 15dB, auto shut off after 15dB on Downlink
Gain Flatness
EGSM & WCDMA
Tpy≤ 8dB
DCS1800MHz
Tpy≤ 12dB
Noise Figure
≤ 8dB
VSWR
≤ 3.0
Group Delay
≤ 1.0μs
Frequency stability
≤ 0.01ppm
Intelligent Functions
Standard
ISO(Donor antenna and Service antenna)
Flickering per 1s when the Isolation is not enough; it lights up when is normal.
Uplink Sleep Mode
Flickering per 1s when there is no users in the coverage. The uplink circuit will shut off, and the ground noise will be less than -70dBm.
Light up when there are users in the coverage.
Smart Mode
Automatically adjust the gain in both of uplink and downlink according to the specific environment.
Input and Output signal strength
Shown Input signal strength with numerial number.
Shown Output signal strength with signal bars.
LED Alarm
Standard
Power LED
Power Indicator
ALC LED
Orange @ ALC 1~5dB, Red @ ALC 15dB~20dB,
LED off after 5 seconds red
Mechanical Specifications
Standard
I /O Port
N-Female
Impedance
50 ohm
Operating Temperature
-25ºC~+55ºC
Environment Conditions
IP40
Dimensions
150*210*36mm
Weight
≤ 2.5Kg
Power Supply
Input AC100~240V,output DC 12V / 3A